| 1. | Cardinal Gates Safety Gate MG25 User Guide MG25 DuraGate FOR OPENINGS 26 5 67cm 41 5 105cm Average installed height 29 5 75cm ASSEMBLY INSTRUCTIONS 1 Place gate on top of carton to establish height Use short screws C for doorframes or longer screws D into drywall to reach a stud 2 Level gate by adjusting telescoping tube attached to upper gate with alien wrench F 3 Loosen width adjustment set screws at top and bottom of gate with alien wrench F slightly to allow gate to expand |
 |
||||||||||||
| 1. |
 |
Cardinal Gates Safety Gate EX-5 User Guide MODEL EX 5 EXTENSION KIT TO ACCOMPANY MODEL SS 30 ASSEMBLY I NSTRUCTI ONS of hinge bracket To secure hinge insert key ring S through hole in end of hinge rod the bottom of the BX2 extension when inserting lower hex bolt b OMount SS 30 6 Now move to SS 30 instruct |
 |
|||||||||||
| 2. |
 |
Cardinal Gates Safety Gate SG-1 User Guide OPTIONAL MODEL SG 1 THE STEP OVER GATE FOR SMALL BREEDS 2 Extend gate to desired width and re tighten screws HINT Gate can be placed against door jam for extra stability see above GATE WARRANTY Your Cardinal Gate is warranted to be free of manufacturing defects for a p |
|
|||||||||||
| 3. |
 |
Cardinal Gates Automobile Alarm 948A-40 User Guide Victoreen 948A 40 and 948A 50 Remote Alarm and Alarm Meter Instruction Manual CardinalMealth Blank Page Contents Section 1 Introduction 1 1 1 1 General Description 1 1 1 2 Application 1 1 1 3 Specifications 1 1 1 4 Receiving Inspection 1 2 1 5 Storage 1 2 1 6 Procedures Warnings and Cautions 1 2 Section 2 Installation 2 1 2 1 Installation 2 1 Section 3 Operation 3 1 3 1 Operation 3 1 3 2 Theory of Operation 3 1 Section 4 Maintenance Cali |
|
|||||||||||
| 4. |
 |
Cardinal Gates Pet Fence XTG User Guide MODEL XTG EXTRA TALL FREESTANDING GATE 3 Slip feet onto bottom of gate 2 Extend gate to desired width and re tighten screws HINT Gate can be placed against door jam for extra stability see above GATE WARRANTY Your Cardinal Gate is warranted to be free of manufacturi |
|
|||||||||||
| 5. |
 |
Cardinal Gates Safety Gate MG15 User Guide MG15 Auto Lock Gate ASSEMBLY INSTRUCTIONS 1 Install hinge bracket A to wall stationary side of gate using Phillips screw C beginning W above floor surface Use ruler on left edge of this sheet to measure from floor Be sure nuts are tight CO of mounted |
|
|||||||||||
| 6. |
 |
Cardinal Gates Safety Gate MG25 User Guide MG25 DuraGate FOR OPENINGS 26 5 67cm 41 5 105cm Average installed height 29 5 75cm ASSEMBLY INSTRUCTIONS 1 Place gate on top of carton to establish height Use short screws C for doorframes or longer screws D into drywall to reach a stud 2 Level gate by adjusting telescoping tube attached to upper gate with alien wrench F 3 Loosen width adjustment set screws at top and bottom of gate with alien wrench F slightly to allow gate to expand |
|
|||||||||||
| 7. |
 |
Cardinal Gates Safety Gate CP30 User Guide CLEAR GATE MODEL CP30 FOR OPENINGS 26 5 67cm 41 5 105cm ASSEMBLY I NSTRUCTI ONS A r BCP_ IJ J mmmsQ mrn S lt G fS H 5 0 OVMWlt Q lt omQ E d V K N stop bracket y r o i 6 A mk |
|
|||||||||||
| 8. |
 |
Cardinal Gates Safety Gate PG-35 User Guide AUTOLOCK PRESSURE GATE MODEL PG 35 FOR OPENINGS 29 X 33 1 4 74cm 85cm ASSEMBLY INSTRUCTIONS THIS GATE IS NOT RECOMMENDED FOR TOP OF STAIRWAY USE A 31019 EXTRA STABILITY MOUNTNG DISKS mmsmQ e OPTION INSTALL WALL MOUNTS IN STEP FOUR BEFORE THIS STEP TWO IF DESIRED 1 Extend both bottom extension rods to wall centering gate in opening expanding no more than 2 1 4 6 cm Tighten in place with wrench 2 Extend top hinge side |
|
|||||||||||